Campbell-scientific CS106 Barometer Uživatelský manuál

INSTRUCTION MANUAL CS106 Barometric Pressure Sensor Revision: 9/14 Copyright © 1995- 2014 Campbell Scientific, Inc.

CS106 Barometric Pressure Sensor 3. When Short Cut opens, select New Program. 4. Select Datalogger Model and Scan Interval (default of 5 seconds i

CS106 Barometric Pressure Sensor 5. Under the Available Sensors and Devices list, select Sensors | Meteorological | Barometric Pressure folder. Sele

CS106 Barometric Pressure Sensor 7. Select any other sensors you have, then finish the remaining Short Cut steps to complete the program. The remain

CS106 Barometric Pressure Sensor 6.2 Accuracy Total Accuracy***: ±0.3 mb @ +20 °C ±0.6 mb @ 0 to +40 °C ±1 mb @ –20 to +45 °C ±1.5 mb @

CS106 Barometric Pressure Sensor 7. Installation 7.1 Jumper Settings The CS106 can be operated in one of two modes: shutdown and normal. The mode

CS106 Barometric Pressure Sensor for mounting the CS106, and hardware for mounting the ENC100 to a tripod, tower, or pole. FIGURE 7-2. ENC100 is a v

CS106 Barometric Pressure Sensor 7.3 Wiring 7.3.1 Datalogger Connection Before connecting the barometer to the datalogger, a yellow warning label mu

CS106 Barometric Pressure Sensor TABLE 7-1. Signal and Ground Connectors for CS106 Wire CS106 Terminal Datalogger Single-Ended Measurement Datalogg

CS106 Barometric Pressure Sensor 7.4 Programming Short Cut is the best source for up-to-date datalogger programming code. Programming code is needed

CS106 Barometric Pressure Sensor Volt (SE) (P1) 1: 1 Reps 2: 25 2500 mV 60 Hz Rejection Range 3: 1 SE Channel 4: 1 Loc [ CS106 ]

CS106 Barometric Pressure Sensor 8.2 Conversion Factors In the example programs, the pressure is reported in millibars (mb). To report pressure in d

CS106 Barometric Pressure Sensor 8.5 Correcting Pressure to Sea Level The weather service, most airports, radio stations, and television stations adj

CS106 Barometric Pressure Sensor 14

Appendix A. Importing Short Cut Code Into CRBasic Editor This tutorial shows: • How to import a Short Cut program into a program editor for additio

Appendix A. Importing Short Cut Code Into CRBasic Editor Once the file is edited with CRBasic Editor, Short Cut can no longer be used to edit the da

Appendix B. Example Programs B.1 CRBasic Programs B.1.1 Example CR1000 Program Using Sequential Mode This CR1000 program uses the sequential mode,

Appendix B. Example Programs B.1.2 Example CR1000 Program Using Pipeline Mode Although this example is for the CR1000, other CRBasic dataloggers, su

Appendix B. Example Programs B.2 Edlog Program Although this example is for the CR10X, other Edlog dataloggers, such as the CR510, CR23X, 21X, and C

Appendix B. Example Programs *Table 3 Subroutines End Program -Input Locations- 1 CS106 1 1 1 B-4

Limited Warranty “Products manufactured by CSI are warranted by CSI to be free from defects in materials and workmanship under normal use and service

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbe

Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing

Precautions DANGER — MANY HAZARDS ARE ASSOCIATED WITH INSTALLING, USING, MAINTAINING, AND WORKING ON OR AROUND TRIPODS, TOWERS, AND ANY ATTACHMENTS TO

Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to spec

Table of Contents B. Example Programs .... B-1 B.1 CRBasic Programs ...

CS106 Barometric Pressure Sensor 1. Introduction The CS106 measures barometric pressure for the range of 500 to 1100 mb. This range equates to from