Campbell-scientific RAWS-H Remote Automated Weather Station Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Měřící nástroje Campbell-scientific RAWS-H Remote Automated Weather Station. Campbell Scientific RAWS-H Remote Automated Weather Station User Manual [es] Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - Automated Weather Station

RAWS-H RemoteAutomated Weather StationRevision: 12/13 Copyright © 2006-2013Campbell Scientific, Inc.

Strany 2

RAWS-H Remote Automated Weather Station • areas where snow drifts occur • low places holding standing water after rains 3.3 Precipitation A rain ga

Strany 3 - Warranty

RAWS-H Remote Automated Weather Station TABLE 4-1. TEMP/RH Connector (color coded orange) Connector Pin Description CR1000 Terminal A Temperature

Strany 4 - Assistance

RAWS-H Remote Automated Weather Station 4.4 Wind Speed and Direction The wind set attaches to the connector labeled WS/WD; this connector is color co

Strany 5 - Table of Contents

RAWS-H Remote Automated Weather Station TABLE 4-6. FM/FT Connector (color coded brown) Connector Pin Description CR1000 TerminalA CS205 Temperatur

Strany 6

RAWS-H Remote Automated Weather Station The SP10-Handar 10 watt solar panel is recommended for a RAWS where NO communication equipment is used. The S

Strany 7 - Station

RAWS-H Remote Automated Weather Station FIGURE 5-1. 12 volt charger/regulator 5.2.2 Wiring The leads from the RAWS connector panel “BATT CHARGER/SO

Strany 8

RAWS-H Remote Automated Weather Station 5.2.3 Troubleshooting If a problem is suspected, the CH100 may be checked by measuring: • input voltage bet

Strany 9 - 2. Getting Started

RAWS-H Remote Automated Weather Station 5.4 GOES Transmitter 5.4.1 General Description The High Data Rate GOES transmitter (pn TX320) shown in FIGUR

Strany 10 - 4. Sensor Wiring

RAWS-H Remote Automated Weather Station FIGURE 5-2. GOES transmitter 5.4.2 Wiring The TX320 is mounted inside the RAWS environmental enclosure and

Strany 11 - 4.3 Solar Radiation

RAWS-H Remote Automated Weather Station 5.4.3 Troubleshooting If a problem is suspected, the TX320 may be checked by measuring the +12 V and Ground t

Strany 13 - 5.1 Solar Panels

RAWS-H Remote Automated Weather Station 5.5.2 Wiring The CR1000KD connects to the CR1000’s CS I/O connector using the 10873 cable that ships with the

Strany 14 - 5.2 Charger/Regulator

RAWS-H Remote Automated Weather Station 5.6.2 Wiring The CR1000 is mounted inside the RAWS environmental enclosure and fastened to the CR1000 printed

Strany 15 - 5.2.2 Wiring

RAWS-H Remote Automated Weather Station 8. References AASC, 1985: The State Climatologist (1985) Publication of the American Association of State Cli

Strany 16 - 5.3 Battery

RAWS-H Remote Automated Weather Station in FIGURE 9-3. Note that when a negative number is subtracted from a positive number, the resulting arithmeti

Strany 17 - 5.4 GOES Transmitter

RAWS-H Remote Automated Weather Station FIGURE 9-2. A declination angle east of True North (positive) is subtracted from 360 (0) degrees to find Tru

Strany 18 - 5.4.2 Wiring

RAWS-H Remote Automated Weather Station 9.2 USGS Web Calculator The USGS provides an easy way of determining the declination of a specific site. Sin

Strany 19 - 5.5 CR1000 Keyboard/Display

RAWS-H Remote Automated Weather Station 20

Strany 20 - 5.6 CR1000 Datalogger

Appendix A. Equipment Wiring and Connector Panel Jumper Location FIGURE A-1. RAWS-H equipment wiring A-1

Strany 21 - 6. Desiccant

Appendix A. Equipment Wiring and Connector Panel Jumper Location FIGURE A-2. RAWS-H connector panel schematic 1 of 2 A-2

Strany 22 - 9. RAWS Orientation

Appendix A. Equipment Wiring and Connector Panel Jumper Location FIGURE A-3. RAWS-H connector panel schematic 2 of 2 A-3

Strany 23

Warranty “PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in materi

Strany 24

Appendix A. Equipment Wiring and Connector Panel Jumper Location Page A-2 P22 Jumper 1 to A-4 FIGURE A-4. RAWS-H connector panel jum

Strany 26

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbel

Strany 27

Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing

Strany 28

Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to spec

Strany 29

Table of Contents ii 5.6 CR1000 Datalogger ... 14 5.6.1 General Description.

Strany 30 - Default Jumper Locations

RAWS-H Remote Automated Weather Station 1. Introduction The RAWS-H allows customers who own a Handar Data Collection Platform to upgrade to a Campbe

Strany 31

RAWS-H Remote Automated Weather Station CR1000KD packed in foam (may go here) FIGURE 1-2. Inside environmental enclosure (optional equipment shown)

Strany 32

RAWS-H Remote Automated Weather Station 2. Getting Started Set up and test your station before field deployment. Keep this manual and the CR1000KD Ke

Komentáře k této Příručce

Žádné komentáře