Campbell-scientific RTDAQ Software Uživatelský manuál Strana 261
- Strana / 368
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Section 9. Calibration and Zeroing
The following values of the mode variable are used to initiate a calibration
process:
1 Start the calibration, OR start the first point of a two point calibration
4 Start the second point of a two point calibration
For Zeroing and Offset calibration, a mode value of 4 is never
used. The entire calibration process is initiated with the mode
value being set to 1.
NOTE
By properly changing the known value variables and the mode variables in a
calibrating program, a manual calibration can be performed on a sensor. Steps
for doing this are given below.
9.4.2 Using the Mode Variable for Manual Single-Point
Calibration
These steps demonstrate how to perform manual single-point calibrations
(Zeroing or Offset calibrations):
1. Ensure the status (value of the mode variable) is 0 or 6 before you start.
a. A number greater than 0 that is not 6 indicates that a calibration is in
progress or that the last calibration did not complete properly.
b. A number less than 0 indicates that the calibration process
encountered an error. Resolve the error before proceeding with the
calibration then set the mode value to zero for a fresh start.
2. Place the sensor into the zeroing or offset condition.
3. Indicate the known offset value (if applicable) by changing the “known
value” variable to that value.
4. Set the mode variable to 1 to initiate the calibration process.
5. Note that the datalogger automatically sets the mode variable to 2 during
the calibration process.
6. Note that the mode variable is set to 6 automatically by the datalogger
when the calibration process completes.
9.4.3 Using the Mode Variable for Manual Two-Point Calibration
These steps demonstrate how to perform manual two-point calibrations
(Multiplier/Offset or Multiplier Only):
1. Ensure the status (value of the mode variable) is 0 or 6 before you start.
a. A number greater than 0 that is not 6 indicates that a calibration is in
progress or that the last calibration did not complete properly.
9-7
- Revision: 3/12 1
- Campbell Scientific, Inc 3
- RTDAQ Table of Contents 5
- Appendices 12
- Figures 13
- Section 1. Introduction 19
- 1.1 RTDAQ Overview 20
- 1.1.3 Monitor Data 21
- 1.1.4 Collect Data 24
- 1.1.7 View Pro 26
- 1.1.8 Split 27
- 1.1.9 CardConvert 27
- 1.1.10 Short Cut 27
- 1.1.11 CRBasic Editor 28
- 1.3 Windows Conventions 29
- 2.1 Hardware and Software 31
- Backup Procedures 33
- 3.2.1.1 Program Directory 34
- 3.2.1.2 Working Directories 34
- 3.2.2.1 Performing a Backup 36
- 4.1 Overview 37
- 4.2 EZSetup Wizard 39
- 4.2.2 Communication Setup 40
- 4.2.3 Datalogger Settings 40
- 4.2.5 Send Program 41
- 4.3 Clock/Program Tab 42
- 4.4 Monitor Data Tab 43
- 4.5 Collect Data Tab 44
- 4.6 Pull-down Menus 45
- 4.6.3 Datalogger Menu 46
- 4.6.3.4 File Control 48
- 4.6.3.5 Calibration Wizard 51
- 4.6.3.6 Terminal Emulator 52
- 4.6.4 Network Menu 53
- 4.6.5 Tools Menu 54
- 4.6.5.2 Options 55
- 4.6.5.3 LogTool 55
- 4.6.5.4 PakBus Graph 57
- 4.7 The RTDAQ Toolbar 59
- Editing 61
- 5.1.3 Toolbar 65
- 5.1.3.1 Compile 67
- 5.1.3.4 Templates 71
- 5.1.4 CRBasic Programming 80
- 5.1.4.5 Line Continuation 82
- 5.1.4.7 Example Program 84
- 5.1.4.8 Data Tables 84
- 5.1.4.10 Numerical Entries 87
- 5.1.4.12 Flags 89
- 5.1.4.13 Parameter Types 89
- 5.2 Short Cut 91
- Datalogger 106
- 5.2.3 Short Cut Settings 107
- 5.2.3.5 Sensor Support 108
- 5.2.3.6 Integration 109
- 5.2.3.7 Font 109
- Generator 110
- 5.3.2 Program Startup 111
- 5.3.4.2 File 113
- 5.3.4.1 File 113
- 5.3.4.3 File 114
- 5.3.4.7 File 115
- 5.3.5 Using Save and Send 116
- 5.3.5.1 Download 117
- 5.3.5.2 Run Options 118
- 5.3.5.3 Datalogger Response 118
- Section 6. View Pro 119
- 6.2 The Toolbar 120
- 6.3 Opening a File 122
- 6.4.1 Selecting a Database 123
- SQL Server 124
- 6.4.2 Selecting a Table 126
- 6.5 Importing a CSV File 127
- 6.6 Data View 129
- 6.7 Graphs 131
- 6.7.1 Line Graph 132
- 6.7.1.2 Graph Width 133
- 6.7.1.3 Scrolling 134
- 6.7.1.4 Graph Cursor 134
- 6.7.1.5 Line Graph Toolbar 135
- 6.7.2 Histogram 136
- 6.7.2.2 Options 139
- 6.7.2.3 Histogram Toolbar 139
- 6.7.3 XY Plot 140
- 6.7.3.3 XY Plot Toolbar 141
- 6.7.4 Rainflow Histogram 142
- 6.7.4.2 Options 144
- 6.7.5 FFT 146
- 6.7.5.2 Options 148
- 6.7.5.3 FFT Toolbar 148
- 6.8 Right-click-Menus 149
- 6.9 Printing Options 151
- 6.10 View Pro Online Help 152
- 7.1.5.1 Display Tab 157
- 7.1.5.2 Alarms Tab 158
- 7.1.5.3 Setup Tab 159
- 7.2 Ports and Flags 160
- 7.3 Table Monitor 161
- 7.3.2.1 Start and Stop 163
- 7.3.2.2 Reset Table 164
- 7.3.2.3 Fields and Values 164
- 7.4 Real Time Graph 166
- 7.4.2 Adding Ite 168
- 7.4.4 Basic Graph Operation 168
- 7.4.5 Zooming a 170
- 7.4.9 Setting th 174
- 7.4.9.3 Visual Disp 177
- 7.4.9.5 Using Save 180
- 7.5 Fast Graph 181
- 7.6 XY Plot 182
- 7.6.2 Setting up 184
- the XY Plot for Display 184
- Points per Field 186
- 7.6.2.2 Number of 186
- 7.6.2.3 Right-Click 187
- Functionality 187
- 7.6.5 Zooming w 193
- 7.6.6.1 Scaling Tab 195
- 7.6.6.2 Data Display Tab 196
- 7.6.6.3 Visual Display Tab 197
- 7.6.6.4 Trace Tab 197
- 7.6.6.5 Save Tab 199
- 7.7 Histogram Monitoring 200
- 7.7.2 Displaying 201
- Histograms 201
- 7.8.2 FFT vs. FFTSample 203
- 7.9.1 Moving an 205
- 7.9.3 Using the Buttons 206
- 7.9.4 3D View 207
- 7.9.5 X-Axis Mode 209
- 7.9.8.1 Scaling the Axes 212
- Options 217
- 7.10 Rainflow Hi 218
- 7.10.6 X-Axis Mode 224
- 7.10.9 Setting th 227
- 7.10.9.3 Trace Options 229
- 7.11 Saving and 232
- Loading Configurations 232
- 7.11.2 Using Co 233
- Control Software 235
- 8.1.1 The RTMC Workspace 237
- 8.1.3 Display Components 237
- 8.1.4.1 File Menu 239
- 8.1.4.2 Edit Menu 240
- 8.1.4.3 View Menu 240
- 8.1.4.4 Project Menu 241
- 8.1.4.5 Screen Menu 241
- 8.1.4.6 Component Menu 242
- 8.1.5 Expressions 243
- 8.1.5.1 Operators 246
- 8.1.5.2 Order of Precedence 246
- 8.1.5.5 Functions 247
- Description 248
- 8.1.5.9 Time Functions 250
- AvgRunOverTimeWithReset 251
- MaxRunOverTimeWithReset 251
- 8.2 RTMC Run-time 252
- 9.1 Calibration Essentials 255
- 9.3.1 Zeroing 257
- 9.3.2 Offset Calibration 258
- Control 260
- Calibration 261
- Programs 263
- Section 10. Utilities 271
- 10.1.2.1 File Format 272
- 10.1.2.2 File Processing 273
- 10.1.2.3 File Naming 274
- 10.1.2.4 TOA5/TOB1 Format 274
- 10.1.3 Converting the File 275
- 10.2.1 Overview 277
- 10.2.4 Terminal Tab 281
- 10.2.6 Off-line Mode 282
- 10.3 Split 283
- 10.3.2 Getting Started 284
- 10.3.3.1 Input Files 290
- Examples: 314
- Monthly Summary Example 317
- Table-based dataloggers 322
- 10.3.3.2 Output Files 324
- 10.3.4 Help Option 330
- 10.3.5 Editing Commands 331
- 10.3.7 Log Files 336
- 10.4.1 Event Logging 337
- 10.4.2 CQR Log (RF Link) 354
- Formats 357
- A.1.2 TOB1 358
- A.2 Datalogger Data Formats 359
- A.3 Binary Data Value Types 361
- A.3.4 IEEE8 362
- A.4.1 Split 362
- A.4.2 CardConvert 362
- Step 1 of 3 363
- Step 2 of 3 364
- Step 3 of 3 365
Související produkty a manuály pro Software Campbell-scientific RTDAQ Software
Muvit MUSLI0536 manuals
Owner’s manuals and user’s guides for Mobile phone cases Muvit MUSLI0536.
We providing 1 pdf manuals Muvit MUSLI0536 for download free by document types: Datasheet
Table of contents
More products and manuals for Mobile phone cases Muvit
| Models | Document Type |
|---|---|
| MUSLI0537 |
Datasheet
Muvit MUSLI0537 mobile phone case,
1 pages
|
| MUCUN0280 |
Datasheet
Muvit MUCUN0280 mobile phone case,
1 pages
|
| MUSLI0525 |
Datasheet
Muvit MUSLI0525 mobile phone case,
1 pages
|
| MUCUN0284 |
Datasheet
Muvit MUCUN0284 mobile phone case,
1 pages
|
| MUSLI0606 |
Datasheet
Muvit MUSLI0606 mobile phone case,
1 pages
|
| SEBMC0039 |
Datasheet
Muvit SEBMC0039 mobile phone case,
1 pages
|
| MUCUN0285 |
Datasheet
Muvit MUCUN0285 mobile phone case,
1 pages
|
| MUSLI0465 |
Datasheet
Muvit MUSLI0465 mobile phone case,
1 pages
|
| SESLI0086 |
Datasheet
Muvit SESLI0086 mobile phone case,
1 pages
|
| MUCUN0281 |
Datasheet
Muvit MUCUN0281 mobile phone case,
1 pages
|
| MUMAG0006 |
Datasheet
Muvit MUMAG0006 mobile phone case,
1 pages
|
| MUCUN0232 |
Datasheet
Muvit MUCUN0232 mobile phone case,
1 pages
|
| MUCUN0278 |
Datasheet
Muvit MUCUN0278 mobile phone case,
1 pages
|
| MUSNS0072 |
Datasheet
Muvit MUSNS0072 mobile phone case,
1 pages
|
| MUSNS0003 |
Datasheet
Muvit MUSNS0003 mobile phone case,
1 pages
|
| MUCUN0227 |
Datasheet
Muvit MUCUN0227 mobile phone case,
1 pages
|
| MUCUN0229 |
Datasheet
Muvit MUCUN0229 mobile phone case,
1 pages
|
| MUSLI0542 |
Datasheet
Muvit MUSLI0542 mobile phone case,
1 pages
|
| MUSLI0563 |
Datasheet
Muvit MUSLI0563 mobile phone case,
1 pages
|
| MUSLI0303 |
Datasheet
Muvit MUSLI0303 mobile phone case,
1 pages
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce